smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.4.0-99-generic] (local build)
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               SAMSUNG
Product:              MZILT7T6HALA/007
Revision:             GXA0
Compliance:           SPC-5
User Capacity:        7 681 501 126 656 bytes [7,68 TB]
Logical block size:   512 bytes
Physical block size:  4096 bytes
LU is resource provisioned, LBPRZ=1
Rotation Rate:        Solid State Device
Form Factor:          2.5 inches
Logical Unit id:      0x5002538b1184df60
Serial number:        S5DDNE0R801692
Device type:          disk
Transport protocol:   SAS (SPL-4)
Local Time is:        Fri Dec 23 16:00:21 2022 MSK
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Percentage used endurance indicator: 0%
Current temperature = 25
Lifetime maximum temperature = 54
Lifetime minimum temperature = 19
Maximum temperature since power on = 25
Minimum temperature since power on = 23
Manufactured in week 32 of year 2021
Accumulated start-stop cycles:  892
Specified load-unload count over device lifetime:  0
Accumulated load-unload cycles:  0
Elements in grown defect list: 0

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0        0         0         0          0      10311,154           0
write:         0        0         0         0          0      11472,811           0
verify:        0        0         0         0          0          0,000           0

Non-medium error count:    10237

  Pending defect count:0 Pending Defects
SMART Self-test log
Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
     Description                              number   (hours)
# 1  Background short  Completed                   -     134                 - [-   -    -]
# 2  Background short  Completed                   -     130                 - [-   -    -]
# 3  Background short  Completed                   -     128                 - [-   -    -]
# 4  Background short  Completed                   -     128                 - [-   -    -]
# 5  Background short  Completed                   -     128                 - [-   -    -]

Long (extended) Self-test duration: 3600 seconds [60,0 minutes]

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 146:02 [8762 minutes]
    Number of background scans performed: 0,  scan progress: 9,34%
    Number of background medium scans performed: 0


Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 3
  number of phys = 1
  phy identifier = 0
    attached device type: SAS or SATA device
    attached reason: unknown
    reason: loss of dword synchronization
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=1 stp=1 smp=1
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5002538b1184df62
    attached SAS address = 0x50000d1704b53280
    attached phy identifier = 3
    Invalid DWORD count = 4
    Running disparity error count = 4
    Loss of DWORD synchronization count = 1
    Phy reset problem count = 0
    Phy event descriptors:
     Received ERROR count: 0
     Received address frame error count: 0
     Received abandon-class OPEN_REJECT count: 0
     Received retry-class OPEN_REJECT count: 8
     Received SSP frame error count: 0
relative target port id = 2
  generation code = 3
  number of phys = 1
  phy identifier = 1
    attached device type: no device attached
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; unknown
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5002538b1184df63
    attached SAS address = 0x0
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization count = 0
    Phy reset problem count = 0
    Phy event descriptors:
     Received ERROR count: 0
     Received address frame error count: 0
     Received abandon-class OPEN_REJECT count: 0
     Received retry-class OPEN_REJECT count: 0
     Received SSP frame error count: 0